bootcmd=run distro_bootcmd bootdelay=1 baudrate=115200 ethprime=FEC ipaddr=192.168.10.2 serverip=192.168.10.1 netmask=255.255.255.0 loadaddr=0x12000000 arch=arm cpu=armv7 board=colibri_imx6 board_name=colibri_imx6 vendor=toradex soc=mx6 mmc_boot=if mmc dev ${devnum}; then setenv devtype mmc; run scan_dev_for_boot_part; fi boot_net_usb_start=usb start usb_boot=usb start; if usb dev ${devnum}; then setenv devtype usb; run scan_dev_for_boot_part; fi boot_prefixes=/ /boot/ boot_scripts=boot.scr.uimg boot.scr boot_script_dhcp=boot.scr.uimg boot_targets=mmc1 mmc0 usb0 dhcp boot_extlinux=sysboot ${devtype} ${devnum}:${distro_bootpart} any ${scriptaddr} ${prefix}extlinux/extlinux.conf scan_dev_for_extlinux=if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}extlinux/extlinux.conf; then echo Found ${prefix}extlinux/extlinux.conf; run boot_extlinux; echo SCRIPT FAILED: continuing...; fi boot_a_script=load ${devtype} ${devnum}:${distro_bootpart} ${scriptaddr} ${prefix}${script}; source ${scriptaddr} scan_dev_for_scripts=for script in ${boot_scripts}; do if test -e ${devtype} ${devnum}:${distro_bootpart} ${prefix}${script}; then echo Found U-Boot script ${prefix}${script}; run boot_a_script; echo SCRIPT FAILED: continuing...; fi; done scan_dev_for_boot=echo Scanning ${devtype} ${devnum}:${distro_bootpart}...; for prefix in ${boot_prefixes}; do run scan_dev_for_extlinux; run scan_dev_for_scripts; done; scan_dev_for_boot_part=part list ${devtype} ${devnum} -bootable devplist; env exists devplist || setenv devplist 1; for distro_bootpart in ${devplist}; do if fstype ${devtype} ${devnum}:${distro_bootpart} bootfstype; then run scan_dev_for_boot; fi; done bootcmd_mmc1=setenv devnum 1; run mmc_boot bootcmd_mmc0=setenv devnum 0; run mmc_boot bootcmd_usb0=setenv devnum 0; run usb_boot bootcmd_dhcp=if dhcp ${scriptaddr} ${boot_script_dhcp}; then source ${scriptaddr}; fi; distro_bootcmd=for target in ${boot_targets}; do run bootcmd_${target}; done boot_file=zImage console=ttymxc0 defargs=galcore.contiguousSize=50331648 user_debug=30 dfu_alt_info=u-boot.imx raw 0x2 0x3ff mmcpart 0;boot part 0 1;rootfs part 0 2;zImage fat 0 1;imx6q-colibri-eval-v3.dtb fat 0 1;imx6q-colibri-cam-eval-v3.dtb fat 0 1 emmcargs=ip=off root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait emmcboot=run setup; setenv bootargs ${defargs} ${emmcargs} ${setupargs} ${vidargs}; echo Booting from internal eMMC chip...; run emmcdtbload; load mmc 0:1 ${kernel_addr_r} ${boot_file} && run fdt_fixup && bootz ${kernel_addr_r} ${dtbparam} emmcdtbload=setenv dtbparam; load mmc 0:1 ${fdt_addr_r} ${fdt_file} && setenv dtbparam " - ${fdt_addr_r}" && true fdt_file=imx6dl-colibri-eval-v3.dtb fdt_fixup=; bootm_size=0x10000000 fdt_addr_r=0x12100000 initrd_high=0xffffffff kernel_addr_r=0x11000000 pxefile_addr_r=0x17100000 ramdisk_addr_r=0x12200000 scriptaddr=0x17000000 nfsargs=ip=:::::eth0:on root=/dev/nfs rw nfsboot=run setup; setenv bootargs ${defargs} ${nfsargs} ${setupargs} ${vidargs}; echo Booting via DHCP/TFTP/NFS...; dhcp ${kernel_addr_r} && run nfsdtbload && run fdt_fixup && bootz ${kernel_addr_r} ${dtbparam} nfsdtbload=setenv dtbparam; tftp ${fdt_addr_r} ${fdt_file} && setenv dtbparam " - ${fdt_addr_r}"; true sdargs=ip=off root=/dev/mmcblk1p2 ro rootfstype=ext4 rootwait sdboot=run setup; setenv bootargs ${defargs} ${sdargs} ${setupargs} ${vidargs}; echo Booting from MMC/SD card; run sddtbload; load mmc 1:1 ${kernel_addr_r} ${boot_file} && run fdt_fixup && bootz ${kernel_addr_r} ${dtbparam} sddtbload=setenv dtbparam; load mmc 1:1 ${fdt_addr_r} ${fdt_file} && setenv dtbparam " - ${fdt_addr_r}" && true setethupdate=if env exists ethaddr; then; else setenv ethaddr 00:14:2d:00:00:00; fi; tftpboot ${loadaddr} flash_eth.img && source ${loadaddr} setsdupdate=setenv interface mmc; setenv drive 1; mmc rescan; load ${interface} ${drive}:1 ${loadaddr} flash_blk.img && source ${loadaddr} setup=setenv setupargs fec_mac=${ethaddr} consoleblank=0 no_console_suspend=1 console=tty1 console=${console},${baudrate}n8 setupdate=run setsdupdate || run setusbupdate || run setethupdate setusbupdate=usb start && setenv interface usb; setenv drive 0; load ${interface} ${drive}:1 ${loadaddr} flash_blk.img && source ${loadaddr} splashpos=m,m vidargs=video=mxcfb0:dev=lcd,640x480M@60,if=RGB666 video=mxcfb1:off fbmem=8M